Pouring plaster into your impression mould is something I have been busy doing all week so I thought I'd pass on a few helpful hints while I'm still in 'casting mode'!
The first thing to remember is this is not an exact science. Many professional sculptors & craftsmen never measure quantities of plaster & water & rely on experience to get the mix they want. It doesn't matter if you add slightly too much powder/water when mixing your casting mix - it should still work out ok. What may vary is the amount of time you have before the mix sets & how strong the final piece is.
Secondly, plaster sets quicker the older it is. If you have a kit which has not been used within 6 months of purchase the plaster is likely to set quicker than stated in the instructions, giving you less working time!
Now for some real advice:
Plaster types: there are many & they vary in coarseness of the powder, hardness & setting time. Our kits use a plaster with a total working time of 5/6 minutes at room temperature. It is a form of dental plaster that gives excellent detail & good hardness whilst not being too hard to carve & sand once dry. There are many other plasters available & if using them you should obtain a data sheet with mixing ratios & setting times & experiment before pouring a mix into your precious baby foot mould!
Adding plaster to water: As a rule, you need 1 part water to 2 parts plaster. You should always add the water to the plaster & not the other way round. Pour the plaster into the water & make a little mountain in the middle of the water. This should be left to soak up the water for 1-2 minutes before you start mixing. This allows the water to be absorbed by the plaster in a nice, even manner & you are less likely to get lumps.
Mixing techniques: Mix from the bottom of the container in smooth circles. You are trying to mix without putting bubbles into the mixture. Mix for a minute or so - the more you mix the faster & harder the plaster will set so don't overdo it! As soon as you have a mix which is smooth like single cream you're almost ready to pour.
Removing bubbles: they are your enemy as they will catch in fingers & toes leaving your cast digitless. Tap the tub of plaster on a hard surface to 'knock out' as many bubbles as possible before pouring into the mould. If pouring a foot, half fill & using the bristle end of a paintbrush, 'paint' around the inside of the mould into every toe & as much of the inside surface as possible. Tap the mould to dislodge any more bubbles & then top the mould right up.
If pouring a hand, fill the mould once, empty the plaster back into the tub & then refill slowly. Clamp a cloth over the open end of the mould & shake well, tipping the mould upside down & shaking it in all planes to give bubbles a chance to escape. Then, remove the cloth, top up the mould & leave to set.
Lots of words here I know but it's all good advice! I think I need a video of these tips - watch this space!!
Weekly news on Creative Castings baby gift products, especially their in house range of baby casting kits, clay imprint kits and inkless print range. Creating 3D replicas of baby hands and feet using casting techniques and passing this knowledge on to others is one of the aims of this blog.
Showing posts with label plaster casting. Show all posts
Showing posts with label plaster casting. Show all posts
Saturday, 29 March 2008
Sunday, 20 January 2008
Use of plaster in moulding children & babies hands & feet .
Julie found an article this week regarding the use of plaster as a moulding material for hands & feet.
This should not be done for several reasons, one of which is highlighted in the articles . A water & plaster mixture is exothermic - that is, heat is given off when the two are mixed together & this CAN cause burns if the mixture is in contact with the skin. Plaster bandage is usually kept slightly off the skin with a layer of vaseline & dues to being applied in thin layers tends not to give rise to the same issues as a tub of plaster mix does.
Have a read & you'll see why we only recommend taking moulds of children's hands & feet with aliginate - an inert, non toxic mixture which is fully biodegradeable. Plus, you'll get much more detail with alginate!
Plaster of Paris Hazard Alert
In an incident a girl was mixing Plaster of Paris with
water by hand, intending to make a plaster cast of
her hand. The mix became very hot, the girl suffered
serious burns and her hands had to be amputated.
The safety Data Sheet supplied with the product did
warn against making casts of the hand.
Although Plaster of Paris is used for setting bones,
in such cases it is never put in direct contact with the
skin and, in addition, it is used in relatively thin layer
so the heat can dissipate. In bulk the temperature can
reach 60°C or so.
Before using plaster of paris to make casts of the
children’s hands or feet, please check with the
product manufacturer that it is safe to do so.
Taken from the Northern Devon District Early Years and Childcare Newsletter, Summer 2007
Link to the original pdf document
Want to buy some alginate for your castign needs? We sell alginate in heat sealed bags on their own or in packs with casting powder & full instruction. Click here to see our alginate & plaster supplies. Data sheets are available for all our materials on request.
This should not be done for several reasons, one of which is highlighted in the articles . A water & plaster mixture is exothermic - that is, heat is given off when the two are mixed together & this CAN cause burns if the mixture is in contact with the skin. Plaster bandage is usually kept slightly off the skin with a layer of vaseline & dues to being applied in thin layers tends not to give rise to the same issues as a tub of plaster mix does.
Have a read & you'll see why we only recommend taking moulds of children's hands & feet with aliginate - an inert, non toxic mixture which is fully biodegradeable. Plus, you'll get much more detail with alginate!
Plaster of Paris Hazard Alert
In an incident a girl was mixing Plaster of Paris with
water by hand, intending to make a plaster cast of
her hand. The mix became very hot, the girl suffered
serious burns and her hands had to be amputated.
The safety Data Sheet supplied with the product did
warn against making casts of the hand.
Although Plaster of Paris is used for setting bones,
in such cases it is never put in direct contact with the
skin and, in addition, it is used in relatively thin layer
so the heat can dissipate. In bulk the temperature can
reach 60°C or so.
Before using plaster of paris to make casts of the
children’s hands or feet, please check with the
product manufacturer that it is safe to do so.
Taken from the Northern Devon District Early Years and Childcare Newsletter, Summer 2007
Link to the original pdf document
Want to buy some alginate for your castign needs? We sell alginate in heat sealed bags on their own or in packs with casting powder & full instruction. Click here to see our alginate & plaster supplies. Data sheets are available for all our materials on request.
Subscribe to:
Posts (Atom)